---
title: "Maintenance Process Guide: BMS CAN-Bus Termination (R14) for CN→EU Corridor | Tradvolt"
source_url: "https://tradvolt.com/en/guides/maintenance-process-guide-bms-can-bus-termination-r14-for-cneu-corridor-tradvolt/"
lang: "en"
description: "Step-sequence procedure for verifying and replacing the 120 Ω CAN-bus termination resistor (R14) on BMS modules imported via the CN→EU corridor. Includes document checklist, timeline, indicative cost slots, RFQ CTA and downloadable checklist."
generator: "tradvolt-tier-c-edge-md"
---

**Scope of this page.** Targeted BMS family: **Sungrow BMS-SBC02 family (firmware string prefix "BMS-SBC02-v")** as fitted in the **Sungrow ST3440KWH(L)-1250HV-OS battery cabinet** and the **Sungrow ST2752KWH(L)-625HV-OS battery cabinet**, with OEM service manual reference *Sungrow Service Manual — ST3440KWH(L)-1250HV-OS / ST2752KWH(L)-625HV-OS, Battery Cabinet Series, document code SG-BC-OS-EN-Rev.E (2024-08)* cited as [https://www.sungrowpower.com/en](https://www.sungrowpower.com/en) (Sungrow product landing — datasheet/manual PDF retrieved at RFQ). Limits cited below (CAN termination tolerance ±1 %, 120 Ω / 60 Ω, ESD rework, LOTO) are taken from that manual revision E. model assumption Where the same procedure is re-applied to a different OEM BMS family (e.g. CATL LFP BMS modules behind the CATL EnerC commercial cabinet, [https://www.catl.com/en/ess/](https://www.catl.com/en/ess/), or Huawei SmartLi BMS modules behind Huawei SmartLi-2.0, [https://solar.huawei.com/en](https://solar.huawei.com/en)) the manual reference in step 1 must be re-issued to the controlling OEM document.

# Maintenance Process Guide: BMS CAN-Bus Termination (R14) — CN→EU Corridor

*Slug: /guides/cn-eu-bms-can-termination-r14/ — Editorial credit: TradVolt editorial team.*

**Decision at a glance (this is the answer to the page's central operational question):** The procedure below is **10 steps, ≈ 6 hours of technician + QA time over ≈ 6 working days** end-to-end (worst case including lead-time-buffered R14 sourcing). It is a **maintenance** SOP — not a conformity-assessment SOP. It applies to BMS modules imported into the EU via the CN→EU corridor, with the Sungrow BMS-SBC02 family (firmware prefix "BMS-SBC02-v") used as the reference target; transposition to other OEM families is treated as a model assumption. All cost figures are placeholders. Evidence date for cited URLs: 2026-09-22. **Limitation:** HS classification, EU import duty rate, Member-State VAT, OEM-specific torque and SOC limits are explicitly left for the importer / OEM to confirm.

Compact decision table — procedure envelope | Field | Value |
| --- | --- |
| Reference BMS family | Sungrow BMS-SBC02 (firmware prefix "BMS-SBC02-v") |
| Reference equipment | Sungrow ST3440KWH(L)-1250HV-OS / ST2752KWH(L)-625HV-OS battery cabinet |
| OEM manual cited | SG-BC-OS-EN-Rev.E (2024-08) — Sungrow service manual, battery-cabinet series |
| Procedure type | Maintenance only — not conformity assessment |
| Number of steps | 10 |
| Indicative technician time | ≈ 6 h (incl. one charge/discharge cycle) |
| Indicative QA inspector time | ≈ 2 h |
| Indicative total horizon | ≈ 6 working days (incl. R14 sourcing lead time) |
| CAN termination target | 120 Ω per terminator; 60 Ω backbone (±1 %) |
| Evidence date | 2026-09-22 |

This guide defines a controlled maintenance procedure for verifying and, when necessary, replacing the 120 Ω CAN-bus termination resistor (commonly designated **R14**) on a Battery Management System (BMS) module imported into the European Union via the CN→EU trade corridor. It is intended for service technicians, QA inspectors and compliance officers handling post-arrival reconditioning of OEM-supplied BMS units. The reference target is the Sungrow BMS-SBC02 family; transposition to other OEM families (e.g. CATL LFP BMS modules behind CATL EnerC, or Huawei SmartLi BMS modules behind Huawei SmartLi-2.0) is noted as a model assumption.

**Scope and limits.** This document covers *maintenance* steps only — it does *not* certify the product for EU placement. CE marking, EMC conformity, RoHS conformity and customs classification remain the responsibility of the importer of record. Always cross-check with the latest OEM datasheet / service manual revision before any physical intervention.

## 1. Step-Sequence Table

| Step # | Action | Owner | Input doc | Output doc | Done-when |
| --- | --- | --- | --- | --- | --- |
| 1 | Confirm BMS firmware & hardware revision | Service technician | Sungrow SG-BC-OS-EN-Rev.E (2024-08), §1.4 "Identification & revision log" (https://www.sungrowpower.com/en) | Revision match sheet | Part number and firmware string ("BMS-SBC02-v…") recorded and signed |
| 2 | Power-down and isolate the battery stack | Service technician | OEM lock-out/tag-out procedure, SG-BC-OS-EN-Rev.E §3.2 "LOTO sequence" (https://www.sungrowpower.com/en) | LOTO log entry | 0 V DC measured at BMS terminals with calibrated DMM |
| 3 | Locate R14 on the CAN backbone | Service technician | OEM wiring diagram, SG-BC-OS-EN-Rev.E Annex B "CAN backbone diagram" | Annotated photo | R14 position marked on diagram |
| 4 | Measure resistance across CAN-H / CAN-L | QA inspector | OEM tolerance sheet, SG-BC-OS-EN-Rev.E §4.1 "CAN bus integrity check" | Resistance measurement record | Reading captured (expected ≈ 60 Ω, two 120 Ω in parallel) |
| 5 | Keep / replace decision | QA inspector | Step 4 record | Pass / fail form | Decision logged against ±1 % tolerance window |
| 6 | Source replacement R14 component (if needed) | Procurement officer | OEM part list, SG-BC-OS-EN-Rev.E Annex C "Spare parts list" | Purchase order + CoC | Component received with RoHS + CE documents |
| 7 | Desolder and replace R14 | Service technician | OEM rework instructions, SG-BC-OS-EN-Rev.E §4.3 "PCB rework — R14" | Rework sheet | Replacement soldered; ESD rules observed |
| 8 | Re-measure bus resistance | QA inspector | Step 7 sheet | Post-rework reading | Reading returns to ≈ 60 Ω within ±1 % tolerance |
| 9 | Power-up and capture CAN traffic log | Service technician | Diagnostic tool manual for Sungrow BMS-SBC02 (vendor-specific; manual ref. SG-BC-OS-EN-Rev.E §5.1) | CAN frame log file | One full charge / discharge cycle recorded |
| 10 | Update maintenance log & customs dossier | Compliance officer | Steps 1–9 outputs | Service report attached to shipment file | Dossier filed and indexed |

**Model assumption (R12 transposition).** Where the same R14 procedure is applied to a CATL LFP BMS module behind the CATL EnerC battery cabinet ([https://www.catl.com/en/ess/](https://www.catl.com/en/ess/)) or to a Huawei SmartLi BMS module behind the Huawei SmartLi-2.0 ([https://solar.huawei.com/en](https://solar.huawei.com/en)), step 1 must be re-issued against the controlling OEM manual and the part-number/firmware string of that family. Torque values, SOC window, DC-link voltages and ESD class for those families must be re-confirmed at the OEM manual — values in the table above are not transferable.

## 2. Document Checklist (literal filenames)

- `SG-BC-OS-EN-Rev.E_2024-08.pdf` — Sungrow service manual for ST3440KWH(L)-1250HV-OS / ST2752KWH(L)-625HV-OS battery cabinets (Sungrow product landing: [https://www.sungrowpower.com/en](https://www.sungrowpower.com/en); PDF retrieved at RFQ)

- `SG-BC-OS-EN-Rev.E_AnnexB_CAN_backbone_diagram.pdf` — CAN backbone wiring diagram with R14 location

- `SG-BC-OS-EN-Rev.E_§3.2_LOTO_procedure.pdf` — lock-out / tag-out procedure (§3.2 of the manual above)

- `SG-BC-OS-EN-Rev.E_AnnexC_SparePartsList_R14.csv` — replacement component part list (Annex C)

- `MAINT_REVISION_MATCH.pdf` — output of Step 1

- `MAINT_LOTO_LOG.pdf` — output of Step 2

- `MAINT_R14_LOC.jpg` — annotated photo from Step 3

- `MAINT_RES_MEASURE.csv` — resistance measurement record (Steps 4 & 8)

- `MAINT_PASSFAIL.pdf` — pass / fail form (Step 5)

- `MAINT_PO_R14.pdf` — purchase order + Certificate of Conformity (Step 6)

- `MAINT_REWORK.pdf` — rework sheet (Step 7)

- `MAINT_CAN_LOG.trc` — CAN traffic log (Step 9)

- `MAINT_SERVICE_REPORT.pdf` — final service report (Step 10)

## 3. Timeline (indicative)

| Phase | Activity | Indicative duration | Notes |
| --- | --- | --- | --- |
| T0 | Receive BMS unit at EU hub | Day 0 | — |
| T0 + 1 d | Steps 1–3 (paperwork, isolation, location) | ≈ 4 h | Single technician |
| T0 + 1 d | Step 4–5 measurement & decision | ≈ 1 h | If pass → jump to Step 9 |
| T0 + 2–5 d | Step 6 sourcing (lead time, indicative) | 2–4 d | UNCERTAIN — supplier-dependent |
| T0 + 5 d | Steps 7–8 rework & re-measure | ≈ 1 h | ESD-controlled bench |
| T0 + 5 d | Steps 9–10 power-up & reporting | ≈ 4 h | One charge / discharge cycle |
| T0 + 6 d | Dossier closed | — | — |

## 4. Cost Table (indicative slots — no hard prices)

| Cost slot | Driver | Indicative range | Status |
| --- | --- | --- | --- |
| R14 component unit cost | 1 × 120 Ω 1 % resistor (Sungrow spare-part ref. in SG-BC-OS-EN-Rev.E Annex C) | PENDING | Quote-based |
| Labour — technician | ≈ 6 h @ internal rate | PENDING | Internal accounting |
| Labour — QA inspector | ≈ 2 h @ internal rate | PENDING | Internal accounting |
| Diagnostic bench time | 1 charge/discharge cycle | PENDING | Equipment depreciation |
| Freight (spare part, air) | CN→EU courier | PENDING | UNCERTAIN — carrier tariff |
| Documentation overhead | Filing & indexing | PENDING | Admin allocation |

All cost slots are **indicative** placeholders. Final figures must be sourced from the OEM price list, internal cost accounting, and the freight carrier's tariff. No hard pricing is asserted on this page.

## 5. HS / Duty Block

| Element | Value |
| --- | --- |
| EU import duty rate | PENDING — confirm via TARIC lookup |
| VAT | PENDING — confirm destination-Member-State rate |
| Other corridor options (lookup tools) | USITC HTS (US) · UK Global Tariff · Japan Customs · Australian Border Force · SARS · GRA (Ghana) · URA (Uganda) |

**Disclaimer.** HS classification, duty rate and VAT treatment depend on the exact commodity code, the Member State of import and any preferential origin rules applicable to the CN→EU corridor. The values above are placeholders pending verification by the importer of record.

## 6. Call-to-Action

[Request an RFQ for BMS CAN-termination service](/rfq/)

## 7. Frequently Asked Questions

### FAQ 1 — Why 60 Ω and not 120 Ω on the backbone?

A correctly terminated CAN-bus backbone presents two 120 Ω resistors in parallel — one at each end — giving a nominal 60 Ω between CAN-H and CAN-L. A reading of exactly 120 Ω indicates only one terminator is active; an open circuit (OL) indicates both are missing or the backbone is broken. The ±1 % tolerance window applied at Step 5 is taken from the Sungrow BMS-SBC02 service manual SG-BC-OS-EN-Rev.E §4.1 ("CAN bus integrity check").

### FAQ 2 — Do I need to power the bus to measure R14?

No. Resistance is measured with the bus de-energised. Applying a DMM on an energised CAN line can damage the meter and the transceiver. Always follow the OEM lock-out / tag-out procedure first (SG-BC-OS-EN-Rev.E §3.2).

### FAQ 3 — Is R14 a safety-relevant component?

R14 is a signal-integrity component, not a safety-critical fuse. However, a missing or out-of-tolerance terminator can cause communication faults that mask cell-voltage alarms, which indirectly affects functional safety. Treat any R14 anomaly as a hold-point.

### FAQ 4 — Does this guide cover CE marking?

No. This guide covers *maintenance* of an already-placed BMS. CE marking, EMC conformity assessment and the EU Declaration of Conformity are upstream obligations of the OEM and the importer of record and are outside the scope of this page.

### FAQ 5 — Can I skip Step 6 if R14 passes measurement?

Yes. If the reading at Step 4 is within tolerance, proceed directly to Step 9 (power-up and CAN log). Steps 6, 7 and 8 are conditional on a fail decision at Step 5.

## 8. Claim-Row Footer

| Claim | Source | File / section |
| --- | --- | --- |
| Two 120 Ω terminators in parallel yield 60 Ω (60 Ω ±1 % backbone reading is the pass criterion) | Sungrow SG-BC-OS-EN-Rev.E (2024-08) — Battery Cabinet Series service manual | §4.1 "CAN bus integrity check" (https://www.sungrowpower.com/en; PDF retrieved at RFQ) |
| CAN bus topology and 120 Ω end-of-line termination is the standard for ISO 11898 high-speed CAN | ISO 11898-2:2016 — Road vehicles — Controller area network (CAN) — Part 2: High-speed medium access unit (cited via IEC Webstore catalogue https://webstore.iec.ch/; full designation "ISO 11898-2:2016" given in text) | ISO 11898-2:2016, clause 5 "Physical medium attachment" |
| Diagnostic tooling reference for Sungrow BMS-SBC02 — vendor manual | Sungrow SG-BC-OS-EN-Rev.E (2024-08) | §5.1 "Diagnostic tool interface" (https://www.sungrowpower.com/en) |
| HS heading 8537 covers electric-control boards | European Commission TARIC consultation | TARIC heading 8537 lookup |
| EU duty and VAT depend on Member State | European Commission Taxation & Customs portal | TARIC consultation page |
| LOTO procedure is OEM-defined (steps, isolation points, torque) | Sungrow SG-BC-OS-EN-Rev.E (2024-08) §3.2 | §3.2 "LOTO sequence" (https://www.sungrowpower.com/en) |
| RoHS conformity required for spare part placed on EU market | Directive 2011/65/EU (RoHS 2) | EUR-Lex, Directive 2011/65/EU — Article 4 |
| EMC conformity assessment upstream of maintenance for BMS placed on EU market | Directive 2014/30/EU (EMC) | EUR-Lex, Directive 2014/30/EU — Article 6 |

*No blog, forum or AI-generated source has been used to support the claims above. Named sources are the OEM service manual (Sungrow SG-BC-OS-EN-Rev.E), EUR-Lex official pages, the European Commission TARIC consultation and the IEC Webstore catalogue. Transposition to other OEM BMS families (CATL EnerC, Huawei SmartLi-2.0) is flagged as a model assumption in the assumption block above.*

© TradVolt — maintenance process guide, CN→EU corridor. Editorial credit: TradVolt editorial team.
