---
title: "UN 38.3 — Definition & China Sourcing Guide | Tradvolt Glossary"
source_url: "https://tradvolt.com/glossary/un38-3/"
lang: "en"
description: "UN 38.3 is the mandatory United Nations transport safety test standard (T.1 to T.8) required for shipping lithium cells, modules, and battery packs from China."
generator: "tradvolt-tier-c-edge-md"
---

[Tradvolt](/)

[← Glossary](/glossary/) · [Methods](/methods/)

# UN 38.3

**UN 38.3** is Section 38.3 of the United Nations *Manual of Tests and Criteria* (ST/SG/AC.10/11), the mandatory international transport safety test standard that all lithium metal and lithium-ion cells, modules, and battery packs must pass before being offered for air, sea, road, or rail freight as Class 9 dangerous goods.

## How it is measured and specified

To demonstrate that lithium batteries can withstand pressure changes, temperature extremes, mechanical vibration, and electrical fault conditions during transit without mass loss, leakage, venting, disassembly, rupture, or fire, UN 38.3 prescribes eight sequential abuse and environmental tests:

- **T.1 Altitude Simulation:** Low-pressure storage at 11.6 kPa for at least 6 hours at 20±5°C.

- **T.2 Thermal Test:** Rapid thermal cycling between +72±2°C and −40±2°C across 10 cycles.

- **T.3 Vibration:** Sinusoidal log-sweep vibration from 7 Hz to 200 Hz across three perpendicular mounting axes.

- **T.4 Shock:** Half-sine mechanical acceleration pulses modeling rough cargo handling.

- **T.5 External Short Circuit:** Short-circuiting terminals at 57±4°C through a total external resistance below 0.1 ohm.

- **T.6 Impact / Crush:** Cell-level mechanical impact or flat/rod crush testing.

- **T.7 Overcharge:** Charging rechargeable battery packs at twice the manufacturer's recommended maximum continuous charge current for 24 hours.

- **T.8 Forced Discharge:** Cell-level forced discharge to evaluate resistance to cell reversal in series strings.

Under Subsection 38.3.5, manufacturers and exporters must provide a standardized **UN 38.3 Test Summary** tying the tested cell or pack model, watt-hour (Wh) rating, and ISO/IEC 17025 testing laboratory details to the physical shipment.

## How it matters when sourcing from China

Ocean carriers and freight forwarders operating out of Chinese export ports (such as Shanghai, Ningbo, Shenzhen, and Xiamen) will reject dangerous-goods bookings if the factory's UN 38.3 Test Summary does not match the exact pack model number, nominal voltage, and watt-hour rating printed on the product nameplate. Lithium-ion shipments travel as Class 9 dangerous goods under **UN 3480** (standalone lithium-ion batteries, such as LFP racks and containers) or **UN 3481** (lithium-ion batteries packed with or contained in equipment, such as solar BoS or EVSE units containing backup cells) governed by UN Model Regulations Packing Instructions P908/P909, the IMDG Code for ocean freight, and the IATA Dangerous Goods Regulations for air cargo.

Tradvolt procurement and pre-shipment workflows enforce strict document-to-nameplate reconciliation before container stuffing:

- The [UN 38.3 documentation audit SOP for the China-to-Ireland corridor](/en/guides/un38-3-documentation-audit-sop-cnie-corridor-tradvolt/) details step-by-step checks of T.1 through T.8 pass results, Subsection 38.3.5 Test Summary completeness, Safety Data Sheet (SDS) consistency, and IMDG / IATA Class 9 marking before booking vessel space.

- The [battery module EOL grading SOP for the China-to-Spain corridor](/en/guides/battery-module-eol-grading-sop-cnes-corridor-lfp-vertical-tradvolt/) ties final factory release of 280 Ah LFP modules to an active UN 38.3 Test Summary and requires resetting pack charge to ≤30% SoC prior to crating.

- Even when importing non-storage hardware such as EV charging stations, the [EVSE pre-shipment inspection SOP for China to New Zealand](/en/guides/pre-shipment-inspection-sop-evse-cnnz-aql-un38-3-re-check-tradvolt/) mandates a UN 38.3 re-check whenever chargers contain internal lithium backup or buffer batteries, alongside [battery TCO supplier document checks](/methods/battery-tco/).

## What to confirm before procurement

- Confirm that the UN 38.3 test report covers the assembled battery pack or module SKU—not solely the raw prismatic cell—unless the pack configuration qualifies under the single-cell/module provisions of Section 38.3.

- Cross-check that the watt-hour rating, model designation, and manufacturer name on the UN 38.3 Test Summary match the commercial invoice, SDS, and physical enclosure label character for character.

- Confirm whether any design change exceeding a 20% mass or electrical threshold has occurred since the test date, which requires re-testing under UN 38.3.3(g).
